3D Printer parts in NZ
-
These simple external filament rollers can be used to put filament rolls of any size outside your printer & feed into the 3d printer. Great to load 3kg spools of filament into smaller printers. This works easily with rolls of any size including 1kg, 3kg, 5kg etc. The bearings allow rolls to turn freely, regardless of weight. The 2 pieces can be placed as far or as near as possible, based on the width of the rolls. Particularly useful for small light weight 3d printers which would otherwise topple when a heavy roll was mounted on them.
-
Carbon Fibre reinforced Steel board Actual board size is 490mm x 305mm Designed to fit our Creatbot F430 PEEK 3d printer but can be used in any machine of similar size. The advantage is that this surface offers very high abrassion resistance. So when you 3d print with high temp materials, the surface can last longer. The other advantage of these boards is that they can be used as removable build plates. We recommend sticking a PEI sheet on this if you want to use them in that way, as PEI is a more versatile surface & not just one for 3d printing PEEK. Please see our 400x300mm PEI sheets here.
-
Genuine Creatbot door handles. These are the slim thin silver coloured aluminum door handles on newer Creatbot 3d printers with hinged doors. They are the smaller size (approx 80mm long), which are used for DX, DE, F160. They are also used on the rear chamber doors of the F430. These are attached to the Acrylic doors on the D series, & corresponding door frames on F series machines.
-
This is the Touch Sensor used on many 3d printers like our Creatbot F430 & new D600 for the Z axi homing & auto level. If the probe tip bends or breaks, you can easily replace the probe. After many months of High Temperature printing, it is common for the probe's internal magnetism to get demagnetised due to the heat in the chamber. This can cause it to stop clicking on & off. Please replace the probe as needed.
-
The Teflon feed tube to connect the extruder to the head on Creatbot D series 3d printers like the Creatbot DX, DE etc. Includes the brass studs that the tube plugs into & locks into place. Screws on the head end & the extruder end. No assembly needed. Available for 3mm filament as well as 1.75mm filament based Creatbot D series machines. Please specify filament diameter, otherwise the default 3mm compatible tubes will be sent as they are more common. If your lugs break off, please consider buying this 1 piece ready tube.
-
Standard Tube Cartridge Heater that slots inside the hot block. Has long wire leads. Suitable for all Creatbot D series 3d printers including DX , DX Plus, DE , DE Plus for all single, dual or triple head models.
-
Genuine Creatbot second generation nozzles. Will suit all Creatbot D series 3D Printers we sell: DM, DX, DE & Plus versions We stock a wide range of nozzle diameters: 0.4, 0.6, 0.8, 1.0 mm
-
This is a temperature sensing Thermocouple for Creatbot D series 3d printers. They will fit all Creatbot DX & DE machines bought since 2015.
-
Genuine Creatbot Throat Tube which connects onto the heat sink on top & the nozzle goes at the bottom. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including DM, DX, DE, the Plus versions, & the older D600 3mm machines
-
Hinges used for many Creatbot 3D Printers. Fits newer version of Creatbot DX, DE & also some versions of F160. Used with the clear plastic panels used on doors. 1 piece. Please buy as many as you need. Standard 40mm hinge that can work for many other applications.
-
Suitable for all Creatbot F series 3d printers including F430, F160, & their PEEK edition 3d printers. Standard Tube Cartridge Heater that slots inside the hot block. Has a small connector to plug on the board.
-
Genuine Creatbot Throat Tube which connects the hot block into the extruder mechanism. This is the Full Matal hot end which doesn't have a teflon liner inside, allowing you to easily print Carbon Fiber as well as high temp materials up to 450C. If you are new to 3d printing, you might find it useful to start with the other Teflon lined heat brake version as it can be easier to print common materials like PLA & ABS with that one. The heat sink & the nozzle is attached at the bottom of this piece. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including F160, F160 PEEK, F430, F430 PEEK, D600 PRO (not the older D600)
