3D Printer parts in NZ
-
A4 Size NFEP Film for medium size SLA Resin 3D Printers NFEP film also called PFA Film is better than standard FEP film to reduce suction forces. It is basically a better quality of the non-stick surface so it reduces peel forces. So parts are less likely to stick to film or pop off from the build plate. This FEP Film is suitable for slightly bigger printers like Phrozen Sonic XL, Phrozen Mighty, Epax E10, Anycubic Mono, Elegoo Saturn etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have 2 FEPs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tyre, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer.
-
Genuine Creatbot second generation nozzles. Will suit all Creatbot D series 3D Printers we sell: DM, DX, DE & Plus versions We stock a wide range of nozzle diameters: 0.4, 0.6, 0.8, 1.0 mm
-
Best Quality Creatbot Martensitic Hardened Steel nozzle for 1.75mm 3d printers. Martensitic Steel nozzles are the best nozzles presently avaialble. They are the most durable nozzles compared to brass or stainless steel. Hardened martensitic steel allows much cleaner retractions than brass nozzles, which interestingly also improves the overall print quality. These nozzles can be used with Carbon Fiber filaments. They are well suited particularly for advanced materials that print at ultra high temps, & even with carbon fibre added to such filaments. Our nozzles are individually machined for optimum precision & longer life (not just die casted like cheap nozzles). Will suit all Creatbot F series 3D Printers we sell: Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers We stock a wide range of nozzle diameters 0.3, 0.4, 0.6, 0.8 mm Our nozzles can also be used with other Mk8 compatible 3d printer heads.
-
New improved easy switch nozzle & hot end for the FlashForge Adventurer series 3D Printer. These nozzles work on Adventurer 3, Adventurer 3 Pro, & Adventurer 4 3d printers. Please choose your nozzle diameter & temperature from the dropdowns. This is a superbly easy to use, unique system that allows you to quickly switch the nozzle, & heater block without any assembly. Just press the clamps on the sides of the head to push this assembly out, & then insert a new one in. They are avilable in 2 temperature options; 240C & 260C. As well as in 2 different sizes, 0.4mm & 0.6mm. These nozzles are stainless steel, so wear much lesser than brass nozzles. With machines like the Adventurer 4, you can buy the 0.6mm nozzle head to print with Carbon Fiber. This is a real advantage for a machine in this price point to now offer Carbon FIber 3d printing capability. For older Adventuer 3 3D Printers (before 2020) we recommend you use the 240C 0.4mm nozzles.
-
Genuine Creatbot Throat Tube which connects the hot block into the extruder mechanism. This is the teflon tube lined version which makes it easy to print PLA, PETg etc thanks to the teflon liner. But it will only operate up to 260C, please do not print hotter than that else you will damage the teflon liner. The heat sink & the nozzle is attached at the bottom of this piece. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including F160, F160 PEEK, F430, F430 PEEK, D600 PRO (not the older D600)
-
Genuine Creatbot standard 260 degree rated hot end for F series 1.75mm 3d printers. Will suit all Creatbot F 3D Printers we sell including Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers. This hot end is only for materials upto 260C. To print hotter, please use buy the High Temp Extruder hot end. The advantage of the standard hot end is that it has a teflon liner inside which aids smooth flow of materials like PLA. However this teflon can be worn off by abrasive materials like Carbon Fiber, so for such materials we recommend printing with the high temp hot end which doesnt have that liner. If you also need a new temperature sensor thermister or thermocouple, or a new cartridge heater, please buy them separately.
-
This is a brand of glue that we have found to work really well on all beds for all 3d printers. You will need glue when 3d printing with Nylon, Carbon Fibre, PolyPropylene, & other materials that don't like to stick to other surfaces. Just apply a thin layer of this glue on a warm build surface, & print directly on it. Please take care that if printing directly on glass beds then some materials can crack the bed when taking it off after using glue. We recommend you buy a PEI sheet first if you plan to print a material with glue. This is a PVA based glue that easily wipes off with a damp cloth. Reapply only as needed. Less is more with Glue when used for 3d printing. 20g glue stick
-
Best Quality Creatbot Martensitic Hardened Steel nozzle for 1.75mm 3d printers. Martensitic Steel nozzles are the best nozzles presently avaialble. They are the most durable nozzles compared to brass or stainless steel. Hardened martensitic steel allows much cleaner retractions than brass nozzles, which interestingly also improves the overall print quality. These nozzles can be used with Carbon Fiber filaments, however please be advised 0.4mm is on the edge, its a bit small for carbon to flow through well. Milled Carbon Fiber Nylon when printing small parts should be ok, but for larger longer prints, recommend using 0.6mm nozzles. These are well suited particularly for advanced materials that print at ultra high temps like PEEK, PEI Ultem, PPSU etc. Our nozzles are individually machined for optimum precision & longer life (not just die casted like cheap nozzles). Will suit all Creatbot F series 3D Printers we sell: Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers We stock a wide range of nozzle diameters 0.3, 0.4, 0.6, 0.8 mm Our nozzles can also be used with other Mk8 compatible 3d printer heads.
-
This is a temperature sensing Thermocouple for Creatbot F series 3d printers. They will fit all Creatbot F430 & F160 3d printers.
-
This is the Touch Sensor used on many 3d printers like our Creatbot F430 & new D600 for the Z axi homing & auto level. If the probe tip bends or breaks, you can easily replace the probe. After many months of High Temperature printing, it is common for the probe's internal magnetism to get demagnetised due to the heat in the chamber. This can cause it to stop clicking on & off. Please replace the probe as needed.
