3D Printer Parts & Accessories

3D Printer parts in NZ

  • This is a brand of glue that we have found to work really well on all beds for all 3d printers. You will need glue when 3d printing with Nylon, Carbon Fibre, PolyPropylene, & other materials that don't like to stick to other surfaces. Just apply a thin layer of this glue on a warm build surface, & print directly on it. Please take care that if printing directly on glass beds then some materials can crack the bed when taking it off after using glue. We recommend you buy a PEI sheet first if you plan to print a material with glue. This is a PVA based glue that easily wipes off with a damp cloth. Reapply only as needed. Less is more with Glue when used for 3d printing. 20g glue stick
  • Hinges used for many Creatbot 3D Printers. Fits newer version of Creatbot DX, DE & also some versions of F160. Used with the clear plastic panels used on doors. 1 piece. Please buy as many as you need. Standard 40mm hinge that can work for many other applications.
  • Pulley for the belt rail system on Wanhao i3 & similar 3d printers. Will work on i3 plus as well new i3 plus mark 2. Is also compatible with many other 3d printers, but please check to be sure.
  • Linear Bearing with outer plastic cover & mount holes. Fit the extruder rail assembly on Wanhao i3 & similar 3d printers. Can also be used as platform bearings. Will work on i3 plus as well new i3 plus mark 2. Is also compatible with many other 3d printers, but please check to be sure.
  • Genuine Creatbot door handles. These are the slim thin silver coloured aluminum door handles on newer Creatbot 3d printers with hinged doors. They are the smaller size (approx 80mm long), which are used for DX, DE, F160. They are also used on the rear chamber doors of the F430. These are attached to the Acrylic doors on the D series, & corresponding door frames on F series machines.
  • Genuine FlashForge nozzle for the FlashForge Guider 2S 3D Printer. It is common for nozzles to wear or block after a period of use, & need replacing. Simply unscrew the existing nozzle & screw the new one on, easy. Please remember to always heat your hot end before removing your nozzle.
  • These simple external filament rollers can be used to put filament rolls of any size outside your printer & feed into the 3d printer. Great to load 3kg spools of filament into smaller printers. This works easily with rolls of any size including 1kg, 3kg, 5kg etc. The bearings allow rolls to turn freely, regardless of weight. The 2 pieces can be placed as far or as near as possible, based on the width of the rolls. Particularly useful for small light weight 3d printers which would otherwise topple when a heavy roll was mounted on them.  
  • These are the drivers used to drive the stepper motors on Creatbot 3d printers. They are used for the X Y Z axi motors as well as for the Extruder motors. Different drivers have been used for the X Y axi as well as for the Z & E1 / E2. Please choose the correct model number. If the model you have is not listed, please contact us & we will set it up for you.
  • Standard Tube Cartridge Heater that slots inside the hot block. Has long wire leads. Suitable for all Creatbot D series 3d printers including DX , DX Plus, DE , DE Plus for all single, dual or triple head models.
  • Suitable for all Creatbot F series 3d printers including F430, F160, & their PEEK edition 3d printers. Standard Tube Cartridge Heater that slots inside the hot block. Has a small connector to plug on the board.
  • Genuine Creatbot Throat Tube which connects onto the heat sink on top & the nozzle goes at the bottom. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including DM, DX, DE, the Plus versions, & the older D600 3mm machines  
  • Genuine Creatbot Throat Tube which connects the hot block into the extruder mechanism. This is the teflon tube lined version which makes it easy to print PLA, PETg etc thanks to the teflon liner. But it will only operate up to 260C, please do not print hotter than that else you will damage the teflon liner. The heat sink & the nozzle is attached at the bottom of this piece. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including F160, F160 PEEK, F430, F430 PEEK, D600 PRO (not the older D600)
  • Genuine Creatbot Throat Tube which connects the hot block into the extruder mechanism. This is the Full Matal hot end which doesn't have a teflon liner inside, allowing you to easily print Carbon Fiber as well as high temp materials up to 450C. If you are new to 3d printing, you might find it useful to start with the other Teflon lined heat brake version as it can be easier to print common materials like PLA & ABS with that one. The heat sink & the nozzle is attached at the bottom of this piece. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including F160, F160 PEEK, F430, F430 PEEK, D600 PRO (not the older D600)
  • This is a Genuine FlashForge brand nozzle for FlashForge Creator Pro 2 IDEX 3D Printers. It is common for nozzles to wear or block after a period of use, & need replacing. Simply unscrew the existing nozzle & screw the new one on, easy. Please remember to always heat your hot end before removing your nozzle.
  • Phrozen screen protector is made of durable and high-transparency material to protect your LCD screen from the risk of resin spilling & damaging your LCD screen. This works beautifully without affecting your prints. Just relevel your bed after you stick it on the lcd screen of your resin 3d printer & you are good to go.
  • This is a temperature sensing Thermocouple for Creatbot D series 3d printers. They will fit all Creatbot DX & DE machines bought since 2015.  
  • Buildtak style Bed Mat designed for the Creatbot F160 & F160 PEEK 3d printer. This is a simple, easy to apply stick on mat that sticks on the bed of the 3d printer. It can even stick on an existing buildtak. Just peel the bottom & use like a sticker. Great adhesion for common materials like PLA, ABS, PETg, TPU. For a high wearing setup you can buy our matching Carbon Fibre Metal Plate to setup a removable bed system.
  • This is a temperature sensing Thermocouple for Creatbot F series 3d printers. They will fit all Creatbot F430 & F160 3d printers.
  • This is a temperature sensor for the newer FlashForge Creator Pro 2 & Creator 3 Pro 3d printers. It is a threaded type that fits into the hot end block. This is not for older flashforge Creator series printers.
  • This is a 24V DC radial fan used as the part cooling fan on Creatbot F430 & F160 3d printers. It is mounted to the side of the extruder 1 (between 1 & 2 if its a dual extruder machine) & plugs into the top extruder board above the head.
  • Genuine Creatbot Stainless nozzle for 1.75mm 3d printers. Hard Stainless nozzles have much longer life than common brass nozzles. Steel allows much cleaner retractions, which interestingly also improves the overall print quality. Stainless steel nozzles can be used with Carbon Fiber. We also sell Hardened martensitic steel nozzles. They are the best nozzles currently available, & are even better suited particularly for advanced materials that print at ultra high temps, & when carbon fibre is also added to such filaments. Our nozzles are individually machined for optimum precision & longer life (not just die casted like cheap nozzles). Will suit all Creatbot F series 3D Printers we sell: Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers We stock a wide range of nozzle diameters 0.3, 0.4, 0.6, 0.8 mm Our nozzles can also be used with other Mk8 compatible 3d printer heads.
  • Genuine Creatbot second generation nozzles. Will suit all Creatbot D series 3D Printers we sell: DM, DX, DE & Plus versions We stock a wide range of nozzle diameters: 0.4, 0.6, 0.8, 1.0 mm  
  • A4 Size NFEP Film for medium size SLA Resin 3D Printers NFEP film also called PFA Film is better than standard FEP film to reduce suction forces. It is basically a better quality of the non-stick surface so it reduces peel forces. So parts are less likely to stick to film or pop off from the build plate. This FEP Film is suitable for slightly bigger printers like Phrozen Sonic XL, Phrozen Mighty, Epax E10, Anycubic Mono, Elegoo Saturn etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have 2 FEPs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tyre, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer.
  • New improved easy switch nozzle & hot end for the FlashForge Adventurer series 3D Printer. These nozzles work on Adventurer 3, Adventurer 3 Pro, & Adventurer 4 3d printers. Please choose your nozzle diameter & temperature from the dropdowns. This is a superbly easy to use, unique system that allows you to quickly switch the nozzle, & heater block without any assembly. Just press the clamps on the sides of the head to push this assembly out, & then insert a new one in. They are avilable in 2 temperature options; 240C & 260C. As well as in 2 different sizes, 0.4mm & 0.6mm. These nozzles are stainless steel, so wear much lesser than brass nozzles. With machines like the Adventurer 4, you can buy the 0.6mm nozzle head to print with Carbon Fiber. This is a real advantage for a machine in this price point to now offer Carbon FIber 3d printing capability. For older Adventuer 3 3D Printers (before 2020) we recommend you use the 240C 0.4mm nozzles.
  • The Teflon feed tube to connect the extruder to the head on Creatbot D series 3d printers like the Creatbot DX, DE etc. Includes the brass studs that the tube plugs into & locks into place. Screws on the head end & the extruder end. No assembly needed. Available for 3mm filament as well as 1.75mm filament based Creatbot D series machines. Please specify filament diameter, otherwise the default 3mm compatible tubes will be sent as they are more common. If your lugs break off, please consider buying this 1 piece ready tube.
  • Best Quality Creatbot Martensitic Hardened Steel nozzle for 1.75mm 3d printers. Martensitic Steel nozzles are the best nozzles presently avaialble. They are the most durable nozzles compared to brass or stainless steel. Hardened martensitic steel allows much cleaner retractions than brass nozzles, which interestingly also improves the overall print quality. These nozzles can be used with Carbon Fiber filaments. They are well suited particularly for advanced materials that print at ultra high temps, & even with carbon fibre added to such filaments. Our nozzles are individually machined for optimum precision & longer life (not just die casted like cheap nozzles). Will suit all Creatbot F series 3D Printers we sell: Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers We stock a wide range of nozzle diameters 0.3, 0.4, 0.6, 0.8 mm Our nozzles can also be used with other Mk8 compatible 3d printer heads.
  • Best Quality Creatbot Martensitic Hardened Steel nozzle for 1.75mm 3d printers. Martensitic Steel nozzles are the best nozzles presently avaialble. They are the most durable nozzles compared to brass or stainless steel. Hardened martensitic steel allows much cleaner retractions than brass nozzles, which interestingly also improves the overall print quality. These nozzles can be used with Carbon Fiber filaments, however please be advised 0.4mm is on the edge, its a bit small for carbon to flow through well. Milled Carbon Fiber Nylon when printing small parts should be ok, but for larger longer prints, recommend using 0.6mm nozzles. These are well suited particularly for advanced materials that print at ultra high temps like PEEK, PEI Ultem, PPSU etc. Our nozzles are individually machined for optimum precision & longer life (not just die casted like cheap nozzles). Will suit all Creatbot F series 3D Printers we sell: Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers We stock a wide range of nozzle diameters 0.3, 0.4, 0.6, 0.8 mm Our nozzles can also be used with other Mk8 compatible 3d printer heads.
  • These relays are used in many 3d printers including the Creatbot F430, D600 & PEEK300. Usually they are used for the Bed heater or the Chamber heater. Please select which relay you want from the list. The triger voltage is 3-32V DC. Please pick the correct type. Be sure before you install it. Relays blow instantly if you get the trigger voltage wrong, or connect the wrong end into the wrong point.
  • Power Interruption Circuit board for Creatbot desktop series D & F series 3d printers including DM , DX / DX Plus & DE / DE Plus 3D, F160 / F160 PEEK & F430 PEEK 3D Printer Printers. For D600 PRO series, PEEK 300 & F1000 series, please contact us for the appropriate part. This circuit board detects if there is a power failure while your Creatbot 3d printer is printing. Then when power resumes & the printer is started, the option to resume to resume the existing print is offered. This circuit is not critical, & the printer can still continue to be used with the board's white wire unplugged. Locations where there are excessive power outages seem to cause this board to blow out more frequently than other places. This is mainly because of spikes & voltage fluctuations in such locations. If you experience the need to frequently replace these, we recommend connecting your printer through a spike protector.
  • This is the genuine full metal angled build platform for Phrozen Sonic Mini & Mini 4K 3D printers. It is a thick solid bed to allow maximum print speeds without distortion. If you print a lot, particularly if you print larger layers at once, then this full metal build plate is the best choice.
  • This is a Carbon Fibre reinforced spring steel sheet designed for the Creatbot F160 & F160 PEEK 3d printer Bed. It allows you to setup an easy removable build plate system by 3d printing on this plate, or attaching your chosen build surface onto this plate. Check out our matching Creatbot F160 Build Tak Bed Mat for a sleek & easy solution. This is a high wear resistant 3d printing surface that can provide good adhesion for PEEK & PEI or other advanced polymers, with appropriate surface glues. Ideal for those who 3d print with such materials extensively. You can print directly on Carbon Fibre plates with any material including PLA, but you must apply a little bit of Glue stick on this plate first. You can also buy our 200x200mm PEI sheet which are perfect to stick on this metal plate.  
  • This is the genuine tapered full metal angled build platform for Phrozen Sonic Mini & Mini 4K 3D printers. It is a fully angled bed to allow the resin to flow down smoothly. Using this build platform will minimize resin accumulation on the top of the plate, allowing it to more readily drip back into the vat during printing. This makes clean-up and print removal faster, easier, and less messy overall so that you can spend more time printing. If you print a lot, or print very fast, or print larger parts, this all-metal build plate is the perfect choice.
  • Garolite is a glass fiber epoxy laminate used when high strength and consistent dimensional stability over high temperature is required. Our G10 sheet is a sticker which has 3M MP468 glue on 1 side. This makes it very easy to install on your existing bed. Be it a spring steel sheet, a carbon fiber sheet, a glass bed, an existing PEI coated bed, or a conventional metal bed - the G10 sticker can be easily applied to any 3d printing situation. Garolite G10 is stiff, strong & hard wearing. This makes it really good as a 3D Printing surface for high wear usage. This sheet will handle bed temps up to 130C. The 500x300 is perfect for 3d printers like the F430 whose beds go up to 120C.
  • NFEP Film 450*280mm for large size Resin 3D Printers PFA (NFEP) is the better version of standard FEP film. This FEP Film is suitable for slightly bigger printers like Phrozen Mega8k, Transform, etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have more FEPs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tyre, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer.