3D Printer Parts & Accessories

3D Printer parts in NZ

  • A4 Size NFEP Film for medium size SLA Resin 3D Printers NFEP film also called PFA Film is better than standard FEP film to reduce suction forces. It is basically a better quality of the non-stick surface so it reduces peel forces. So parts are less likely to stick to film or pop off from the build plate. This FEP Film is suitable for slightly bigger printers like Phrozen Sonic XL, Phrozen Mighty, Epax E10, Anycubic Mono, Elegoo Saturn etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have 2 FEPs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tyre, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer.
  • Genuine Creatbot second generation nozzles. Will suit all Creatbot D series 3D Printers we sell: DM, DX, DE & Plus versions We stock a wide range of nozzle diameters: 0.4, 0.6, 0.8, 1.0 mm  
  • Best Quality Creatbot Martensitic Hardened Steel nozzle for 1.75mm 3d printers. Martensitic Steel nozzles are the best nozzles presently avaialble. They are the most durable nozzles compared to brass or stainless steel. Hardened martensitic steel allows much cleaner retractions than brass nozzles, which interestingly also improves the overall print quality. These nozzles can be used with Carbon Fiber filaments. They are well suited particularly for advanced materials that print at ultra high temps, & even with carbon fibre added to such filaments. Our nozzles are individually machined for optimum precision & longer life (not just die casted like cheap nozzles). Will suit all Creatbot F series 3D Printers we sell: Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers We stock a wide range of nozzle diameters 0.3, 0.4, 0.6, 0.8 mm Our nozzles can also be used with other Mk8 compatible 3d printer heads.
  • New improved easy switch nozzle & hot end for the FlashForge Adventurer series 3D Printer. These nozzles work on Adventurer 3, Adventurer 3 Pro, & Adventurer 4 3d printers. Please choose your nozzle diameter & temperature from the dropdowns. This is a superbly easy to use, unique system that allows you to quickly switch the nozzle, & heater block without any assembly. Just press the clamps on the sides of the head to push this assembly out, & then insert a new one in. They are avilable in 2 temperature options; 240C & 260C. As well as in 2 different sizes, 0.4mm & 0.6mm. These nozzles are stainless steel, so wear much lesser than brass nozzles. With machines like the Adventurer 4, you can buy the 0.6mm nozzle head to print with Carbon Fiber. This is a real advantage for a machine in this price point to now offer Carbon FIber 3d printing capability. For older Adventuer 3 3D Printers (before 2020) we recommend you use the 240C 0.4mm nozzles.
  • Genuine Creatbot Throat Tube which connects the hot block into the extruder mechanism. This is the teflon tube lined version which makes it easy to print PLA, PETg etc thanks to the teflon liner. But it will only operate up to 260C, please do not print hotter than that else you will damage the teflon liner. The heat sink & the nozzle is attached at the bottom of this piece. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including F160, F160 PEEK, F430, F430 PEEK, D600 PRO (not the older D600)
  • Genuine Creatbot standard 260 degree rated hot end for F series 1.75mm 3d printers. Will suit all Creatbot F 3D Printers we sell including Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers. This hot end is only for materials upto 260C. To print hotter, please use buy the High Temp Extruder hot end. The advantage of the standard hot end is that it has a teflon liner inside which aids smooth flow of materials like PLA. However this teflon can be worn off by abrasive materials like Carbon Fiber, so for such materials we recommend printing with the high temp hot end which doesnt have that liner. If you also need a new temperature sensor thermister or thermocouple, or a new cartridge heater, please buy them separately.  
  • This is a brand of glue that we have found to work really well on all beds for all 3d printers. You will need glue when 3d printing with Nylon, Carbon Fibre, PolyPropylene, & other materials that don't like to stick to other surfaces. Just apply a thin layer of this glue on a warm build surface, & print directly on it. Please take care that if printing directly on glass beds then some materials can crack the bed when taking it off after using glue. We recommend you buy a PEI sheet first if you plan to print a material with glue. This is a PVA based glue that easily wipes off with a damp cloth. Reapply only as needed. Less is more with Glue when used for 3d printing. 20g glue stick
  • Best Quality Creatbot Martensitic Hardened Steel nozzle for 1.75mm 3d printers. Martensitic Steel nozzles are the best nozzles presently avaialble. They are the most durable nozzles compared to brass or stainless steel. Hardened martensitic steel allows much cleaner retractions than brass nozzles, which interestingly also improves the overall print quality. These nozzles can be used with Carbon Fiber filaments, however please be advised 0.4mm is on the edge, its a bit small for carbon to flow through well. Milled Carbon Fiber Nylon when printing small parts should be ok, but for larger longer prints, recommend using 0.6mm nozzles. These are well suited particularly for advanced materials that print at ultra high temps like PEEK, PEI Ultem, PPSU etc. Our nozzles are individually machined for optimum precision & longer life (not just die casted like cheap nozzles). Will suit all Creatbot F series 3D Printers we sell: Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers We stock a wide range of nozzle diameters 0.3, 0.4, 0.6, 0.8 mm Our nozzles can also be used with other Mk8 compatible 3d printer heads.
  • This is a temperature sensing Thermocouple for Creatbot F series 3d printers. They will fit all Creatbot F430 & F160 3d printers.
  • This is the Touch Sensor used on many 3d printers like our Creatbot F430 & new D600 for the Z axi homing & auto level. If the probe tip bends or breaks, you can easily replace the probe. After many months of High Temperature printing, it is common for the probe's internal magnetism to get demagnetised due to the heat in the chamber. This can cause it to stop clicking on & off. Please replace the probe as needed.
  • NFEP Film 450*280mm for large size Resin 3D Printers PFA (NFEP) is the better version of standard FEP film. This FEP Film is suitable for slightly bigger printers like Phrozen Mega8k, Transform, etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have more FEPs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tyre, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer.
  • Genuine Creatbot Stainless nozzle for 1.75mm 3d printers. Hard Stainless nozzles have much longer life than common brass nozzles. Steel allows much cleaner retractions, which interestingly also improves the overall print quality. Stainless steel nozzles can be used with Carbon Fiber. We also sell Hardened martensitic steel nozzles. They are the best nozzles currently available, & are even better suited particularly for advanced materials that print at ultra high temps, & when carbon fibre is also added to such filaments. Our nozzles are individually machined for optimum precision & longer life (not just die casted like cheap nozzles). Will suit all Creatbot F series 3D Printers we sell: Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers We stock a wide range of nozzle diameters 0.3, 0.4, 0.6, 0.8 mm Our nozzles can also be used with other Mk8 compatible 3d printer heads.
  • This is a temperature sensing Thermocouple for Creatbot D series 3d printers. They will fit all Creatbot DX & DE machines bought since 2015.  
  • Genuine Creatbot high temp 420 degree rated hot end for F series 1.75mm 3d printers. Will suit all Creatbot F 3D Printers we sell including Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers. This hot end will work for all materials upto 420C. This hot end doesnt have a teflon liner so it can be used with abrasive materials like carbon fibre. It will also work for PLA & other common materials. However, for beginners, we sometimes recommend printing those sorts of entry level materials with the standard temp hot end which has a teflon liner, which aids the smoother flow of PLA. So its a little more forgiving for times when your settings may not be quite perfect. However this teflon can be worn off by abrasive materials like Carbon Fiber, so for such materials we recommend printing with the high temp hot end which doesnt have that liner. If you also need a new temperature sensor thermister or thermocouple, or a new cartridge heater, please buy them separately.
  • Suitable for all Creatbot F series 3d printers including F430, F160, & their PEEK edition 3d printers. Standard Tube Cartridge Heater that slots inside the hot block. Has a small connector to plug on the board.
  • Standard Tube Cartridge Heater that slots inside the hot block. Has long wire leads. Suitable for all Creatbot D series 3d printers including DX , DX Plus, DE , DE Plus for all single, dual or triple head models.
  • Buildtak style Bed Mat designed for the Creatbot F160 & F160 PEEK 3d printer. This is a simple, easy to apply stick on mat that sticks on the bed of the 3d printer. It can even stick on an existing buildtak. Just peel the bottom & use like a sticker. Great adhesion for common materials like PLA, ABS, PETg, TPU. For a high wearing setup you can buy our matching Carbon Fibre Metal Plate to setup a removable bed system.
  • Genuine Creatbot Throat Tube which connects the hot block into the extruder mechanism. This is the Full Matal hot end which doesn't have a teflon liner inside, allowing you to easily print Carbon Fiber as well as high temp materials up to 450C. If you are new to 3d printing, you might find it useful to start with the other Teflon lined heat brake version as it can be easier to print common materials like PLA & ABS with that one. The heat sink & the nozzle is attached at the bottom of this piece. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including F160, F160 PEEK, F430, F430 PEEK, D600 PRO (not the older D600)
  • Genuine Creatbot Throat Tube which connects onto the heat sink on top & the nozzle goes at the bottom. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including DM, DX, DE, the Plus versions, & the older D600 3mm machines  
  • Take away the mess & hassle of cleaning resin 3d prints by hand. The Phrozen Wash & Cure Kit will make your cleaning and curing process faster and easier. Thanks to its large washer and mathcing curing station, it can dry and cure your models all in one go.
    • Clean Delicately With Powerful Vortex - Equipped with a powerful bottom propeller, the washing station effectively cleans your models without causing damage to details.
    • Dunk 10” Wide Building Plate Straight In - With extra-large build volume, you can clean almost any model, no matter how big! Best used with Sonic Mighty 8K and other 10” building plates. 
    • The Dual Fan System Makes Drying Easier Than Ever - Designed with a fan drying mode, you can pop printed models straight into the curing station to dry and cure them in one go.
    • No More Sticky and Unevenly Cured Models - With 405nm UV lights radiating from the back and under the models, the curing station ensures extra effective curing.
    • Time-Saving - Coming as a pair, the 8L washing station and the curing station with the dry & cure function are literal time savers.
  • Latest ACF Film for 15" LCD Resin 3D Printers The new Phrozen ACF film is designed with a non-stick and smoother film surface for more efficient 3D printing. Compared to FEP and PFA (nFEP) film, the ACF film features a better release, reducing the printing time and increasing the success rate. ACF is the strongest, & has the highest tear tolerance. It also has the lowerst peel force so suction forces are minised & you have the best print possible. NFEP film (also called PFA Film) is better than the old FEP film to reduce suction forces. ACF takes this to a whole new level. ACF film is the best choice for printign high performance enginering resins such as the Onyx series, Henkel & BASF industrial series, etc. It is a sginifcatly bettter non-stick surface so it reduces peel forces greatly. So parts are less likely to stick to film or pop off from the build plate. This FEP Film is suitable for the biggest of printers like Phrozen Mega 8K 15", Transform 13", etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have multiple ACFs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tyre, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer when using challenging materials at faster speeds.
  • Phrozen Sonic Saber makes removing supports hassle-free with the power of ultrasonic cutting. With 40,000 blade vibrations per second, this ultrasonic knife helps you trim and finish 3D prints at high-precision margins with ease.
  • These simple external filament rollers can be used to put filament rolls of any size outside your printer & feed into the 3d printer. Great to load 3kg spools of filament into smaller printers. This works easily with rolls of any size including 1kg, 3kg, 5kg etc. The bearings allow rolls to turn freely, regardless of weight. The 2 pieces can be placed as far or as near as possible, based on the width of the rolls. Particularly useful for small light weight 3d printers which would otherwise topple when a heavy roll was mounted on them.  
  • This is a 24V DC radial fan used as the part cooling fan on Creatbot F430 & F160 3d printers. It is mounted to the side of the extruder 1 (between 1 & 2 if its a dual extruder machine) & plugs into the top extruder board above the head.
  • Carbon Fibre reinforced Steel board Actual board size is 490mm x 305mm Designed to fit our Creatbot F430 PEEK 3d printer but can be used in any machine of similar size. The advantage is that this surface offers very high abrassion resistance. So when you 3d print with high temp materials, the surface can last longer. The other advantage of these boards is that they can be used as removable build plates. We recommend sticking a PEI sheet on this if you want to use them in that way, as PEI is a more versatile surface & not just one for 3d printing PEEK. Please see our 400x300mm PEI sheets here.
  • Power Interruption Circuit board for Creatbot desktop series D & F series 3d printers including DM , DX / DX Plus & DE / DE Plus 3D, F160 / F160 PEEK & F430 PEEK 3D Printer Printers. For D600 PRO series, PEEK 300 & F1000 series, please contact us for the appropriate part. This circuit board detects if there is a power failure while your Creatbot 3d printer is printing. Then when power resumes & the printer is started, the option to resume to resume the existing print is offered. This circuit is not critical, & the printer can still continue to be used with the board's white wire unplugged. Locations where there are excessive power outages seem to cause this board to blow out more frequently than other places. This is mainly because of spikes & voltage fluctuations in such locations. If you experience the need to frequently replace these, we recommend connecting your printer through a spike protector.
  • Garolite is a glass fiber epoxy laminate used when high strength and consistent dimensional stability over high temperature is required. Our G10 sheet is a sticker which has 3M MP468 glue on 1 side. This makes it very easy to install on your existing bed. Be it a spring steel sheet, a carbon fiber sheet, a glass bed, an existing PEI coated bed, or a conventional metal bed - the G10 sticker can be easily applied to any 3d printing situation. Garolite G10 is stiff, strong & hard wearing. This makes it really good as a 3D Printing surface for high wear usage. This sheet will handle bed temps up to 130C. The 500x300 is perfect for 3d printers like the F430 whose beds go up to 120C.
  • This is a Genuine FlashForge brand nozzle for FlashForge Creator Pro 2 IDEX 3D Printers. It is common for nozzles to wear or block after a period of use, & need replacing. Simply unscrew the existing nozzle & screw the new one on, easy. Please remember to always heat your hot end before removing your nozzle.
  • Hinges used for many Creatbot 3D Printers. Fits newer version of Creatbot DX, DE & also some versions of F160. Used with the clear plastic panels used on doors. 1 piece. Please buy as many as you need. Standard 40mm hinge that can work for many other applications.
  • The Phrozen Air Purifier is specially designed to address one of the common issues faced by 3D printing enthusiasts - resin odor. Resin, a liquid material used in the 3D printing process, typically emits strong and sometimes unpleasant smells, which can be a nuisance to both the printing environment and the overall printing experience. Furthermore, the purifier is designed to be user-friendly and low-maintenance. It has a convenient control panel that allows users to monitor the filter life and replace them when needed. The compact and sleek design of the purifier makes it easy to integrate into any workspace without occupying too much space. By using the Phrozen Air Purifier, 3D printer users can significantly reduce the resin odor, creating a more pleasant and healthier environment for both themselves and others present in the area. This improved air quality not only enhances the overall printing experience but also ensures a safer and more enjoyable workspace.