-
Genuine Creatbot Throat Tube which connects the hot block into the extruder mechanism. This is the teflon tube lined version which makes it easy to print PLA, PETg etc thanks to the teflon liner. But it will only operate up to 260C, please do not print hotter than that else you will damage the teflon liner. The heat sink & the nozzle is attached at the bottom of this piece. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including F160, F160 PEEK, F430, F430 PEEK, D600 PRO (not the older D600)
-
This is a temperature sensing Thermocouple for Creatbot F series 3d printers. They will fit all Creatbot F430 & F160 3d printers.
-
Genuine Creatbot high temp 420 degree rated hot end for F series 1.75mm 3d printers. Will suit all Creatbot F 3D Printers we sell including Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers. This hot end will work for all materials upto 420C. This hot end doesnt have a teflon liner so it can be used with abrasive materials like carbon fibre. It will also work for PLA & other common materials. However, for beginners, we sometimes recommend printing those sorts of entry level materials with the standard temp hot end which has a teflon liner, which aids the smoother flow of PLA. So its a little more forgiving for times when your settings may not be quite perfect. However this teflon can be worn off by abrasive materials like Carbon Fiber, so for such materials we recommend printing with the high temp hot end which doesnt have that liner. If you also need a new temperature sensor thermister or thermocouple, or a new cartridge heater, please buy them separately.
-
Genuine Creatbot standard 260 degree rated hot end for F series 1.75mm 3d printers. Will suit all Creatbot F 3D Printers we sell including Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers. This hot end is only for materials upto 260C. To print hotter, please use buy the High Temp Extruder hot end. The advantage of the standard hot end is that it has a teflon liner inside which aids smooth flow of materials like PLA. However this teflon can be worn off by abrasive materials like Carbon Fiber, so for such materials we recommend printing with the high temp hot end which doesnt have that liner. If you also need a new temperature sensor thermister or thermocouple, or a new cartridge heater, please buy them separately.
-
Hinges used for many Creatbot 3D Printers. Fits newer version of Creatbot DX, DE & also some versions of F160. Used with the clear plastic panels used on doors. 1 piece. Please buy as many as you need. Standard 40mm hinge that can work for many other applications.
-
Genuine Creatbot Throat Tube which connects onto the heat sink on top & the nozzle goes at the bottom. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including DM, DX, DE, the Plus versions, & the older D600 3mm machines
-
A4 Size NFEP Film for medium size SLA Resin 3D Printers NFEP film also called PFA Film is better than standard FEP film to reduce suction forces. It is basically a better quality of the non-stick surface so it reduces peel forces. So parts are less likely to stick to film or pop off from the build plate. This FEP Film is suitable for slightly bigger printers like Phrozen Sonic XL, Phrozen Mighty, Epax E10, Anycubic Mono, Elegoo Saturn etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have 2 FEPs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tyre, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer.
-
This is a brand of glue that we have found to work really well on all beds for all 3d printers. You will need glue when 3d printing with Nylon, Carbon Fibre, PolyPropylene, & other materials that don't like to stick to other surfaces. Just apply a thin layer of this glue on a warm build surface, & print directly on it. Please take care that if printing directly on glass beds then some materials can crack the bed when taking it off after using glue. We recommend you buy a PEI sheet first if you plan to print a material with glue. This is a PVA based glue that easily wipes off with a damp cloth. Reapply only as needed. Less is more with Glue when used for 3d printing. 20g glue stick
-
Suitable for all Creatbot F series 3d printers including F430, F160, & their PEEK edition 3d printers. Standard Tube Cartridge Heater that slots inside the hot block. Has a small connector to plug on the board.
-
Standard Tube Cartridge Heater that slots inside the hot block. Has long wire leads. Suitable for all Creatbot D series 3d printers including DX , DX Plus, DE , DE Plus for all single, dual or triple head models.
-
New improved easy switch nozzle & hot end for the FlashForge Adventurer series 3D Printer. These nozzles work on Adventurer 3, Adventurer 3 Pro, & Adventurer 4 3d printers. Please choose your nozzle diameter & temperature from the dropdowns. This is a superbly easy to use, unique system that allows you to quickly switch the nozzle, & heater block without any assembly. Just press the clamps on the sides of the head to push this assembly out, & then insert a new one in. They are avilable in 2 temperature options; 240C & 260C. As well as in 2 different sizes, 0.4mm & 0.6mm. These nozzles are stainless steel, so wear much lesser than brass nozzles. With machines like the Adventurer 4, you can buy the 0.6mm nozzle head to print with Carbon Fiber. This is a real advantage for a machine in this price point to now offer Carbon FIber 3d printing capability. For older Adventuer 3 3D Printers (before 2020) we recommend you use the 240C 0.4mm nozzles.
-
This is the Touch Sensor used on many 3d printers like our Creatbot F430 & new D600 for the Z axi homing & auto level. If the probe tip bends or breaks, you can easily replace the probe. After many months of High Temperature printing, it is common for the probe's internal magnetism to get demagnetised due to the heat in the chamber. This can cause it to stop clicking on & off. Please replace the probe as needed.
-
This is a Carbon Fibre reinforced spring steel sheet designed for the Creatbot F160 & F160 PEEK 3d printer Bed. It allows you to setup an easy removable build plate system by 3d printing on this plate, or attaching your chosen build surface onto this plate. Check out our matching Creatbot F160 Build Tak Bed Mat for a sleek & easy solution. This is a high wear resistant 3d printing surface that can provide good adhesion for PEEK & PEI or other advanced polymers, with appropriate surface glues. Ideal for those who 3d print with such materials extensively. You can print directly on Carbon Fibre plates with any material including PLA, but you must apply a little bit of Glue stick on this plate first. You can also buy our 200x200mm PEI sheet which are perfect to stick on this metal plate.
-
Buildtak style Bed Mat designed for the Creatbot F160 & F160 PEEK 3d printer. This is a simple, easy to apply stick on mat that sticks on the bed of the 3d printer. It can even stick on an existing buildtak. Just peel the bottom & use like a sticker. Great adhesion for common materials like PLA, ABS, PETg, TPU. For a high wearing setup you can buy our matching Carbon Fibre Metal Plate to setup a removable bed system.
-
Carbon Fibre reinforced Steel board Actual board size is 490mm x 305mm Designed to fit our Creatbot F430 PEEK 3d printer but can be used in any machine of similar size. The advantage is that this surface offers very high abrassion resistance. So when you 3d print with high temp materials, the surface can last longer. The other advantage of these boards is that they can be used as removable build plates. We recommend sticking a PEI sheet on this if you want to use them in that way, as PEI is a more versatile surface & not just one for 3d printing PEEK. Please see our 400x300mm PEI sheets here.
-
Pulley for the belt rail system on Wanhao i3 & similar 3d printers. Will work on i3 plus as well new i3 plus mark 2. Is also compatible with many other 3d printers, but please check to be sure.
-
Linear Bearing with outer plastic cover & mount holes. Fit the extruder rail assembly on Wanhao i3 & similar 3d printers. Can also be used as platform bearings. Will work on i3 plus as well new i3 plus mark 2. Is also compatible with many other 3d printers, but please check to be sure.
-
This is a temperature sensing Thermocouple for Creatbot D series 3d printers. They will fit all Creatbot DX & DE machines bought since 2015.
-
Power Interruption Circuit board for Creatbot desktop series D & F series 3d printers including DM , DX / DX Plus & DE / DE Plus 3D, F160 / F160 PEEK & F430 PEEK 3D Printer Printers. For D600 PRO series, PEEK 300 & F1000 series, please contact us for the appropriate part. This circuit board detects if there is a power failure while your Creatbot 3d printer is printing. Then when power resumes & the printer is started, the option to resume to resume the existing print is offered. This circuit is not critical, & the printer can still continue to be used with the board's white wire unplugged. Locations where there are excessive power outages seem to cause this board to blow out more frequently than other places. This is mainly because of spikes & voltage fluctuations in such locations. If you experience the need to frequently replace these, we recommend connecting your printer through a spike protector.
-
Genuine Creatbot second generation nozzles. Will suit all Creatbot D series 3D Printers we sell: DM, DX, DE & Plus versions We stock a wide range of nozzle diameters: 0.4, 0.6, 0.8, 1.0 mm
Alex L2023-11-28I have dealt with the 3D Printer Store for several months now and have to say that the experience has been very positive. Zubbin is extremely knowledgeable in this field, enthusiastic, honest and responsive. Pre and Post Purchase customer support has been great. He will have your best interest in mind and will recommend the best product for your needs. My positive experience dealing with him professionally has led me to buy product from him for personal use. We are very lucky to have such a supplier providing these kinds of specialized 3D Printers, Filaments, accessories and services in New Zealand. The rare filaments can sometimes be difficult to source but he will do his best to find alternatives to get what's needed ASAP or even suggest proper alternatives. I am looking forward to future collaboration with this supplier.
Elias Bayless2023-10-18First choice for all my 3d printing needs, the team here really does a great job! Always get my filament here and it arrives really fast and always performs very well in my printer.
Lyle Adams2023-10-18I recently purchased a 3D printer from this business and also took their training. Zubbin's knowledge and assistance is top-notch. He provided valuable insights not only on 3D printing but also related topics. Highly recommended!!
Dylan Cooper2023-09-19Solid company to deal with. I have ordered filament multiple times from this company. I have also been advised on better filament options than what I ordered, which worked out really well. Will continue to shop here!
Maarten van den Heuvel2023-08-21Good prices, fast shipping, excellent communication and when there was a hiccup with my order it was sorted super fast and to my full satisfaction. Can recommend.
Phil Shimmin2023-08-16Great service from these guys. On my most recent order there was a stellar turnaround of only 24 hours between initial stock query and the filament being in my printer.
Dan King2022-09-29Shipping and packaging was excellent and best in market pricing. I had an issue with a misunderstanding about the particular properties of the resin I purchased but Zubbin responded quickly and helped me resolve the issue. Perfect customer service, they have gained a loyal customer.
Mike O2022-09-12These guys are awesome. I used to buy my filament from overseas for my projects and needed something in a hurry and went looking for something local. I'm so glad I did. Not only are the prices as good or better than what I was getting overseas and even more of a deal when considering the pricing I was paying for shipping their turn around each time has been next day. Great range of in stock filaments, good prices, super fast turn around and excellent customer service.
Dion Hitchens2022-08-09Kia ora, This is a fantastic business selling reliable machines at a great price point. What I am impressed with the most is that the owner is always willing to help if I have a problem his insight and knowledge he is so willing to share is always on point and allows me to solve the problem I am trying to resolve. I look forward to doing more business with them. thanks
Michael Williams2022-06-28Sent them an email explaining what I was trying to achieve and asked for their advice. They responded promptly and recommend a basic 3d printer which turned out absolutely fit for purpose. Ordered online and with good communication i had printer within days. Will definitely return when I upgrade. This printing stuff is very addictive.