Resin 3d printer parts

Parts like FEP sheets, NFEP, Vat trays, platforms etc commonly used in LCD resin 3d printers like Phrozen, EPAX, Anycubic, Elegoo, Creality & many others.

  • Phrozen screen protector is made of durable and high-transparency material to protect your LCD screen from the risk of resin spilling & damaging your LCD screen. This works beautifully without affecting your prints. Just relevel your bed after you stick it on the lcd screen of your resin 3d printer & you are good to go.
  • A4 Size NFEP Film for medium size SLA Resin 3D Printers NFEP film also called PFA Film is better than standard FEP film to reduce suction forces. It is basically a better quality of the non-stick surface so it reduces peel forces. So parts are less likely to stick to film or pop off from the build plate. This FEP Film is suitable for slightly bigger printers like Phrozen Sonic XL, Phrozen Mighty, Epax E10, Anycubic Mono, Elegoo Saturn etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have 2 FEPs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tyre, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer.
  • This is the genuine full metal angled build platform for Phrozen Sonic Mini & Mini 4K 3D printers. It is a thick solid bed to allow maximum print speeds without distortion. If you print a lot, particularly if you print larger layers at once, then this full metal build plate is the best choice.
  • This is the genuine tapered full metal angled build platform for Phrozen Sonic Mini & Mini 4K 3D printers. It is a fully angled bed to allow the resin to flow down smoothly. Using this build platform will minimize resin accumulation on the top of the plate, allowing it to more readily drip back into the vat during printing. This makes clean-up and print removal faster, easier, and less messy overall so that you can spend more time printing. If you print a lot, or print very fast, or print larger parts, this all-metal build plate is the perfect choice.
  • NFEP Film 450*280mm for large size Resin 3D Printers PFA (NFEP) is the better version of standard FEP film. This FEP Film is suitable for slightly bigger printers like Phrozen Mega8k, Transform, etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have more FEPs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tyre, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer.
  • The Phrozen Air Purifier is specially designed to address one of the common issues faced by 3D printing enthusiasts - resin odor. Resin, a liquid material used in the 3D printing process, typically emits strong and sometimes unpleasant smells, which can be a nuisance to both the printing environment and the overall printing experience. Furthermore, the purifier is designed to be user-friendly and low-maintenance. It has a convenient control panel that allows users to monitor the filter life and replace them when needed. The compact and sleek design of the purifier makes it easy to integrate into any workspace without occupying too much space. By using the Phrozen Air Purifier, 3D printer users can significantly reduce the resin odor, creating a more pleasant and healthier environment for both themselves and others present in the area. This improved air quality not only enhances the overall printing experience but also ensures a safer and more enjoyable workspace.
  • Latest ACF Film for 15" LCD Resin 3D Printers The new Phrozen ACF film is designed with a non-stick and smoother film surface for more efficient 3D printing. Compared to FEP and PFA (nFEP) film, the ACF film features a better release, reducing the printing time and increasing the success rate. ACF is the strongest, & has the highest tear tolerance. It also has the lowerst peel force so suction forces are minised & you have the best print possible. NFEP film (also called PFA Film) is better than the old FEP film to reduce suction forces. ACF takes this to a whole new level. ACF film is the best choice for printign high performance enginering resins such as the Onyx series, Henkel & BASF industrial series, etc. It is a sginifcatly bettter non-stick surface so it reduces peel forces greatly. So parts are less likely to stick to film or pop off from the build plate. This FEP Film is suitable for the biggest of printers like Phrozen Mega 8K 15", Transform 13", etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have multiple ACFs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tyre, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer when using challenging materials at faster speeds.
  • Genuine E10 resin tray molded using non corrosive plastic. This vat fits all EPAX E10 series 3D printers. Works with the original 8.9" screen E10 as well the new 10.1" E10 5K 3d printers. Each vat comes with a sheet of nFEP film already installed, ready to use. Just remove the old tray out & slide the new one in. Thats it, easy installation.
    • Molded tank allows for cheap replacements and extras for switching out resin on the fly
    • Fibreglass reinforced plastic sports increased durability and resistance to corrosion and resin.
    • It is equipped with a rubber seal to ensure that the vat is water-tight to help avoid resin leaks.
    • E10 Vat Max Volume 1500mL without build platform and 700mL with build platform
  • Latest ACF Film for 10" LCD Resin 3D Printers - Pack of 3 films The new Phrozen ACF film is designed with a non-stick and smoother film surface for more efficient 3D printing. Compared to FEP and PFA (nFEP) film, the ACF film features a better release, reducing the printing time and increasing the success rate. ACF is the strongest, & has the highest tear tolerance. It also has the lowest peel force so suction forces are minimised & you have the best print possible. NFEP film (also called PFA Film) is better than the old FEP film to reduce suction forces. ACF takes this to a whole new level. ACF film is the best choice for printing high performance engineering resins such as the Onyx series, Henkel & BASF industrial series, etc. It is a signifcatly better non-stick surface so it reduces peel forces greatly. So parts are less likely to stick to film or pop off from the build plate. This FEP Film is suitable for slightly bigger printers like Phrozen Mighty 8K, Mini 8k, Phrozen Sonic XL, Epax E10, Anycubic Mono, Elegoo Saturn etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have 2 FEPs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tire, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer.
  • This is an upgraded, full metal build platform for EPAX E10 3D printers. It is compatible with all version of the E10 printer including the new E10 5K. The unique top bracket has been specially designed to fit E10 printers for optimum performance. It is a fully angled bed to allow the resin to flow down smoothly. Using this build platform will minimize resin accumulation on the top of the plate, allowing it to more readily drip back into the vat during printing. This makes clean-up and print removal faster, easier, and less messy overall so that you can spend more time printing. If you print a lot, or print very fast, or print larger parts, this all-metal build plate is the perfect choice.
  • Why use Ultrasonic cleaners when Wash & Cure units seem to be so easy to use? Short answer, high speed & less manual work. Ultrasonic vibrations loosen out debris from any surface surface efficiently & quickly using harmless forces. The frequency of motion they form safely dislodges uncured resin particles at a microscopic level that other devices cant create. Ultrasonic cleaners can clean most resin parts in 3 mins. Most entry level washers can't beat that. The fact that there is no heavy movement, allows debris to settle rather than float around. This makes it far easier to get the parts clean with less fluid use. When cleaning castable resins or industrial resins in particular, ultrasonic cleaners will give you the edge.
  • Phrozen Sonic Saber makes removing supports hassle-free with the power of ultrasonic cutting. With 40,000 blade vibrations per second, this ultrasonic knife helps you trim and finish 3D prints at high-precision margins with ease.
  • Take away the mess & hassle of cleaning resin 3d prints by hand. The Phrozen Wash & Cure Kit will make your cleaning and curing process faster and easier. Thanks to its large washer and mathcing curing station, it can dry and cure your models all in one go.
    • Clean Delicately With Powerful Vortex - Equipped with a powerful bottom propeller, the washing station effectively cleans your models without causing damage to details.
    • Dunk 10” Wide Building Plate Straight In - With extra-large build volume, you can clean almost any model, no matter how big! Best used with Sonic Mighty 8K and other 10” building plates. 
    • The Dual Fan System Makes Drying Easier Than Ever - Designed with a fan drying mode, you can pop printed models straight into the curing station to dry and cure them in one go.
    • No More Sticky and Unevenly Cured Models - With 405nm UV lights radiating from the back and under the models, the curing station ensures extra effective curing.
    • Time-Saving - Coming as a pair, the 8L washing station and the curing station with the dry & cure function are literal time savers.