3D Printer parts in NZ
-
Magigoo HT adhesive is designed to provide bed adhesion with challenging materials like PEI Ultem, PEEK, PEKK, PPS, PSU, PPSU etc. It can be used with all kinds of bed surfaces, however we recommend PEI or Garolite. It can also be used with Carbon Fiber reinforced filaments & Glass Filled materials, like PPS-CF, PEI-CF & PEEK-CF etc. To 3D Print Nylon, we recommend Magigoo PA as a first choice, & if that doesn't suit well for your particular filament, then try this Magigoo HT. For common materials like PLA, ABS etc, we recommend buying the Magigoo original glue. Magigoo glue reduces warping in FDM 3D printers. Warping is caused by the differential cooling of a print during a 3D printing process made up of layers. For printing advanced materials reliably, apply a thin layer of Magigoo on your print bed before printing. This will ensure a successful print. If too much glue has been lacquered on, please wipe with a damp sponge & then reapply glue.
-
Magigoo Original adhesive is designed to provide optimum bed adhesion with PLA, ABS, ASA, PETG & other common materials. It can be used with all kinds of bed surfaces, however we recommend PEI or Garolite. It can also be used with Carbon Fiber reinforced filaments & Glass Filled materials. To 3D Print Nylon, we recommend Magigoo PA. For higher temp filaments including PEI & PEEK, we also have Magigoo HT. Magigoo glue reduces warping in FDM 3D printers. Warping is caused by the differential cooling of a print during a 3D printing process made up of layers. For printing advanced materials reliably, apply a thin layer of Magigoo on your print bed before printing. This will ensure a successful print. If too much glue has been lacquered on, please wipe with a damp sponge & then reapply glue.
-
Magigoo PA adhesive is specifically designed for 3D printing with polyamide (nylon) filaments. It offers a strong adhesion to the bed for polyamide based filaments. It can be used with all kinds of bed surfaces, however we recommend PEI or Garolite for Nylon. It can also be used with Carbon Fiber reinforced Nylon & Glass Filled Nylons. When printing with higher temp filaments including Nylon 6 Carbon based filaments, if the Magigoo PA doesnt perform very well in your application, we also have Magigoo HT, which may work better in some cases. Magigoo glue reduces warping in FDM 3D printers. Warping is caused by the differential cooling of a print during a 3D printing process made up of layers. For printing Nylon reliably, apply a thin layer of Magigoo PA on your print bed before printing in nylon filaments. This will ensure a successful print. If too much glue has been lacquered on, please wipe with a damp sponge & then reapply glue.
-
This is the latest flexible build plate that fits on the new magnetic beds of FlashForge Creator 4 3D Printers. It now has a PEI reinforced build surface that provides excellent adhesion to most common materials including flexible TPU materials. It also gives a very good bottom surface finish. It is superior to the older Black plates that FlashForge used to supply. We highly recommend PEI sheets as the best surface to print on. For Nylon based materials, we still recommend you put a thin layer of the glue stick on it.
-
This is the small PCB that goes behind the extruders of a Creatbot F430 head. The main ribbon cable connects to it from the motherboard underneath the machine. And other connectors such as the temp sensors, cartridge heaters, probe etc plug into this little board.
-
Genuine 10" 8K Mono LCD Screen for Phrozen Mighty 8K Resin 3d printer. This is a high quality durable screen designed to give you the best long lasting performance you can expect. If your LCD screen gets damaged, or you see the exposure affected, it might be time to change your LCD. This is the masking LCD screen which projects the UV light layers for your 3d print. It is not the small touch screen panel used to control the printer.
-
Latest ACF Film for 10" LCD Resin 3D Printers - Pack of 3 films The new Phrozen ACF film is designed with a non-stick and smoother film surface for more efficient 3D printing. Compared to FEP and PFA (nFEP) film, the ACF film features a better release, reducing the printing time and increasing the success rate. ACF is the strongest, & has the highest tear tolerance. It also has the lowest peel force so suction forces are minimised & you have the best print possible. NFEP film (also called PFA Film) is better than the old FEP film to reduce suction forces. ACF takes this to a whole new level. ACF film is the best choice for printing high performance engineering resins such as the Onyx series, Henkel & BASF industrial series, etc. It is a signifcatly better non-stick surface so it reduces peel forces greatly. So parts are less likely to stick to film or pop off from the build plate. This FEP Film is suitable for slightly bigger printers like Phrozen Mighty 8K, Mini 8k, Phrozen Sonic XL, Epax E10, Anycubic Mono, Elegoo Saturn etc Can also work with smaller DLP LCD 3D Printers, simply cut the sheet in half & you have 2 FEPs! This will work with Metal or Plastic vats. Very easy to use. Simply open the screws on your vat, remove the old FEP sheet, & put this sheet in place. Please see the video below to see how easily you can change the FEP on your Phrozen Sonic Mini Resin 3D Printers. You should change your FEP film when its cloudy, has excessive scratches, or you find the prints stick to it too easily rather than the bed. Depending on several factors, this is usually around 200 hrs of use. FEP is like a car tire, you can have the best mechanics but without a good tyre, you're asking for trouble. We keep our prices on consumables cheap to help kiwis get the best results with 3d printers without prolonging the need to replace important components. Also check out the PlateBond Adhesion Promotor to help your base layers stick better to the bed of your resin 3d printer.
-
Phrozen screen protector is made of durable and high-transparency material to protect your LCD screen from the risk of resin spilling & damaging your LCD screen. This works beautifully without affecting your prints. Just relevel your bed after you stick it on the lcd screen of your resin 3d printer & you are good to go.
-
This is the USB reader board used on a Creatbot F430 & F160 3d printer. This is the Latest version board with an adapter to allow certain older printer models to also be able to use it.
-
These simple external filament rollers can be used to put filament rolls of any size outside your printer & feed into the 3d printer. Great to load 3kg spools of filament into smaller printers. This works easily with rolls of any size including 1kg, 3kg, 5kg etc. The bearings allow rolls to turn freely, regardless of weight. The 2 pieces can be placed as far or as near as possible, based on the width of the rolls. Particularly useful for small light weight 3d printers which would otherwise topple when a heavy roll was mounted on them.
-
The Phrozen Air Purifier is specially designed to reduce the odour from printing Resins & Filaments in 3d printers that do not have activated air filters. The compact and sleek design of the purifier makes it easy to integrate into any workspace without occupying too much space. They can sit snugly within most machines, & can reduce the VOCs exiting the units. Resins & Filaments used in the 3D printing process, sometimes emit strong smells, which can be a nuisance to both the printing environment and the overall printing experience. The purifier is designed to be user-friendly and low-maintenance. It has a convenient control panel that allows users to monitor the filter life and replace them when needed. By using the Phrozen Air Purifier, 3D printer users can significantly reduce the resin odor, creating a more pleasant and healthier environment for both themselves and others present in the area. This improved air quality not only enhances the overall printing experience but also ensures a safer and more enjoyable workspace. This little device helps alleviate one of the common issues faced by 3D printing enthusiasts.
-
This is a 24V DC radial fan used as the part cooling fan on Creatbot F430 & F160 3d printers. It is mounted to the side of the extruder 1 (between 1 & 2 if its a dual extruder machine) & plugs into the top extruder board above the head.
