3D Printer parts in NZ
-
Linear Bearing with outer plastic cover & mount holes. Fit the extruder rail assembly on Wanhao i3 & similar 3d printers. Can also be used as platform bearings. Will work on i3 plus as well new i3 plus mark 2. Is also compatible with many other 3d printers, but please check to be sure.
-
The Teflon feed tube to connect the extruder to the head on Creatbot D series 3d printers like the Creatbot DX, DE etc. Includes the brass studs that the tube plugs into & locks into place. Screws on the head end & the extruder end. No assembly needed. Available for 3mm filament as well as 1.75mm filament based Creatbot D series machines. Please specify filament diameter, otherwise the default 3mm compatible tubes will be sent as they are more common. If your lugs break off, please consider buying this 1 piece ready tube.
-
This is an upgraded, full metal build platform for EPAX E10 3D printers. It is compatible with all version of the E10 printer including the new E10 5K. The unique top bracket has been specially designed to fit E10 printers for optimum performance. It is a fully angled bed to allow the resin to flow down smoothly. Using this build platform will minimize resin accumulation on the top of the plate, allowing it to more readily drip back into the vat during printing. This makes clean-up and print removal faster, easier, and less messy overall so that you can spend more time printing. If you print a lot, or print very fast, or print larger parts, this all-metal build plate is the perfect choice.
-
This is the genuine tapered full metal angled build platform for Phrozen Sonic Mini & Mini 4K 3D printers. It is a fully angled bed to allow the resin to flow down smoothly. Using this build platform will minimize resin accumulation on the top of the plate, allowing it to more readily drip back into the vat during printing. This makes clean-up and print removal faster, easier, and less messy overall so that you can spend more time printing. If you print a lot, or print very fast, or print larger parts, this all-metal build plate is the perfect choice.
-
This is the genuine full metal angled build platform for Phrozen Sonic Mini & Mini 4K 3D printers. It is a thick solid bed to allow maximum print speeds without distortion. If you print a lot, particularly if you print larger layers at once, then this full metal build plate is the best choice.
-
So we have fast resin 3d printers now, but have you thought about post processing faster? Take away the mess & hassle of cleaning resin 3d prints by hand. And dont wait nearly 50 mins to be able to use your 3d prints with conventional wash & cure devices. With our Ultrasonic 40KHz industrial style washer & a Heated UV Curer, you will speed up your post processing time down to just 15 mins. Thats just 15 mins from when your print is out to when a usable part is in your hand. Standard curers do not heat the chamber. Heating not only speeds up the cure, but more importantly, it significantly improves the internal structural integrity of your part. Normal washer devices tend to rely only on the standard dissolution rate of resin into the cleaner. Whereas ultrasonic cleaners actively separate the resin stuck to the part with a 40KHz wave, thus speeding up the cleaning process dramatically. Wash for just 5 mins with resin cleaning liquid in the ultrasonic & then cure for 10 mins in the heated curer - you have your self a factory quality usable 3d printed part!
-
Why use Ultrasonic cleaners when Wash & Cure units seem to be so popular? Ultrasonic vibrations loosen out debris from any surface surface efficiently & quickly using harmless forces. The frequency of motion they form safely dislodges uncured resin particles at a microscopic level that other devices cant create. Ultrasonic cleaners can clean most resin parts in 3 mins. Most entry level washers can't beat that. The fact that there is no heavy movement, allows debris to settle rather than float around. This makes it far easier to get the parts clean with less fluid use. Resin cleaning liquids like Monocure Resin away & Phrozen now make it a cheaper & safer option than to use IPA or other explosive alcohol based cleaners. When cleaning castable resins or industrial resins in particular, ultrasonic cleaners will give you the edge.
-
Genuine Creatbot door handles. These are the slim thin silver coloured aluminum door handles on newer Creatbot 3d printers with hinged doors. They are the smaller size (approx 80mm long), which are used for DX, DE, F160. They are also used on the rear chamber doors of the F430. These are attached to the Acrylic doors on the D series, & corresponding door frames on F series machines.
-
Why use Ultrasonic cleaners when Wash & Cure units seem to be so easy to use? Short answer, high speed & less manual work. Ultrasonic vibrations loosen out debris from any surface surface efficiently & quickly using harmless forces. The frequency of motion they form safely dislodges uncured resin particles at a microscopic level that other devices cant create. Ultrasonic cleaners can clean most resin parts in 3 mins. Most entry level washers can't beat that. The fact that there is no heavy movement, allows debris to settle rather than float around. This makes it far easier to get the parts clean with less fluid use. When cleaning castable resins or industrial resins in particular, ultrasonic cleaners will give you the edge.
-
This is the latest flexible build plate that fits on the new magnetic beds of FlashForge Creator 4 3D Printers. It now has a PEI reinforced build surface that provides excellent adhesion to most common materials including flexible TPU materials. It also gives a very good bottom surface finish. It is superior to the older Black plates that FlashForge used to supply. We highly recommend PEI sheets as the best surface to print on. For Nylon based materials, we still recommend you put a thin layer of the glue stick on it.
-
Magigoo PA adhesive is specifically designed for 3D printing with polyamide (nylon) filaments. It offers a strong adhesion to the bed for polyamide based filaments. It can be used with all kinds of bed surfaces, however we recommend PEI or Garolite for Nylon. It can also be used with Carbon Fiber reinforced Nylon & Glass Filled Nylons. When printing with higher temp filaments including Nylon 6 Carbon based filaments, if the Magigoo PA doesnt perform very well in your application, we also have Magigoo HT, which may work better in some cases. Magigoo glue reduces warping in FDM 3D printers. Warping is caused by the differential cooling of a print during a 3D printing process made up of layers. For printing Nylon reliably, apply a thin layer of Magigoo PA on your print bed before printing in nylon filaments. This will ensure a successful print. If too much glue has been lacquered on, please wipe with a damp sponge & then reapply glue.
-
Magigoo Original adhesive is designed to provide optimum bed adhesion with PLA, ABS, ASA, PETG & other common materials. It can be used with all kinds of bed surfaces, however we recommend PEI or Garolite. It can also be used with Carbon Fiber reinforced filaments & Glass Filled materials. To 3D Print Nylon, we recommend Magigoo PA. For higher temp filaments including PEI & PEEK, we also have Magigoo HT. Magigoo glue reduces warping in FDM 3D printers. Warping is caused by the differential cooling of a print during a 3D printing process made up of layers. For printing advanced materials reliably, apply a thin layer of Magigoo on your print bed before printing. This will ensure a successful print. If too much glue has been lacquered on, please wipe with a damp sponge & then reapply glue.
-
Magigoo HT adhesive is designed to provide bed adhesion with challenging materials like PEI Ultem, PEEK, PEKK, PPS, PSU, PPSU etc. It can be used with all kinds of bed surfaces, however we recommend PEI or Garolite. It can also be used with Carbon Fiber reinforced filaments & Glass Filled materials, like PPS-CF, PEI-CF & PEEK-CF etc. To 3D Print Nylon, we recommend Magigoo PA as a first choice, & if that doesn't suit well for your particular filament, then try this Magigoo HT. For common materials like PLA, ABS etc, we recommend buying the Magigoo original glue. Magigoo glue reduces warping in FDM 3D printers. Warping is caused by the differential cooling of a print during a 3D printing process made up of layers. For printing advanced materials reliably, apply a thin layer of Magigoo on your print bed before printing. This will ensure a successful print. If too much glue has been lacquered on, please wipe with a damp sponge & then reapply glue.
-
Extruder Circuit Board for FlashForge Adventurer 3 3D Printers
-
Genuine Wanhao Branded lower metal sheet to be stuck on the printer platform, on which you can then use magnetic mats & magnetic sensors. This is used on Wanhao i3 Mk2 (also called i3 v2) 3d printers, the new version of D5s, & other such machines. This is not the actual print surface, its the metal sheet on which the build surface sticks magnetically. For older version of the i3 please buy the other BuildTak style bed mat which has glue on one side. Works extremely well for most materials like PLA, ABS & PETG.
-
Head board for 3d printers like Wanhao i3 plus mk2, D6, D9, D9 mk2 etc. This is the little PCB that sits on top of the main head where you plug in the heater, temp sensors, etc.
