-
These relays are used in many 3d printers including the Creatbot F430, D600 & PEEK300. Usually they are used for the Bed heater or the Chamber heater. Please select which relay you want from the list. The triger voltage is 3-32V DC. Please pick the correct type. Be sure before you install it. Relays blow instantly if you get the trigger voltage wrong, or connect the wrong end into the wrong point.
-
Genuine E10 resin tray molded using non corrosive plastic. This vat fits all EPAX E10 series 3D printers. Works with the original 8.9" screen E10 as well the new 10.1" E10 5K 3d printers. Each vat comes with a sheet of nFEP film already installed, ready to use. Just remove the old tray out & slide the new one in. Thats it, easy installation.
- Molded tank allows for cheap replacements and extras for switching out resin on the fly
- Fibreglass reinforced plastic sports increased durability and resistance to corrosion and resin.
- It is equipped with a rubber seal to ensure that the vat is water-tight to help avoid resin leaks.
- E10 Vat Max Volume 1500mL without build platform and 700mL with build platform
-
This is a Carbon Fibre reinforced spring steel sheet designed for the Creatbot F160 & F160 PEEK 3d printer Bed. It allows you to setup an easy removable build plate system by 3d printing on this plate, or attaching your chosen build surface onto this plate. Check out our matching Creatbot F160 Build Tak Bed Mat for a sleek & easy solution. This is a high wear resistant 3d printing surface that can provide good adhesion for PEEK & PEI or other advanced polymers, with appropriate surface glues. Ideal for those who 3d print with such materials extensively. You can print directly on Carbon Fibre plates with any material including PLA, but you must apply a little bit of Glue stick on this plate first. You can also buy our 200x200mm PEI sheet which are perfect to stick on this metal plate.
-
This is the small PCB that goes behind the extruders of a Creatbot F430 head. The main ribbon cable connects to it from the motherboard underneath the machine. And other connectors such as the temp sensors, cartridge heaters, probe etc plug into this little board.
-
This is the USB reader board used on a Creatbot F430 & F160 3d printer. This is the Latest version board with an adapter to allow certain older printer models to also be able to use it.
-
This is a temperature sensor for the newer FlashForge Creator Pro 2 & Creator 3 Pro 3d printers. It is a threaded type that fits into the hot end block. This is not for older flashforge Creator series printers.
-
This motor is used in the Creatbot F430 3d printer. It is the X axi motor that connects on the linear rail to move the head left to right. This is the motor only, not the fan/heatsink. Please remember to put the heatsink & fan from your old motor onto the new motor.
-
Full Swappable Extruder Head for the new FlashForge Creator 4 3D Printer. 3 Extruder options available: HS Extruder = High Temp 360C Extruder including Carbon Fiber filled materials. HT Extruder = upto 320C temp for common plastics including PLA/ABS. F Extruder = Specialist flexible filament extruder for high flex TPU TPE & similar materials. Please specify which head you want on the order notes.
-
Genuine FlashForge nozzle for the FlashForge Guider 2S 3D Printer. It is common for nozzles to wear or block after a period of use, & need replacing. Simply unscrew the existing nozzle & screw the new one on, easy. Please remember to always heat your hot end before removing your nozzle.
-
Head board for 3d printers like Wanhao i3 plus mk2, D6, D9, D9 mk2 etc. This is the little PCB that sits on top of the main head where you plug in the heater, temp sensors, etc.
-
Genuine Wanhao Branded lower metal sheet to be stuck on the printer platform, on which you can then use magnetic mats & magnetic sensors. This is used on Wanhao i3 Mk2 (also called i3 v2) 3d printers, the new version of D5s, & other such machines. This is not the actual print surface, its the metal sheet on which the build surface sticks magnetically. For older version of the i3 please buy the other BuildTak style bed mat which has glue on one side. Works extremely well for most materials like PLA, ABS & PETG.
-
Extruder Circuit Board for FlashForge Adventurer 3 3D Printers
-
This is the latest flexible build plate that fits on the new magnetic beds of FlashForge Creator 4 3D Printers. It now has a PEI reinforced build surface that provides excellent adhesion to most common materials including flexible TPU materials. It also gives a very good bottom surface finish. It is superior to the older Black plates that FlashForge used to supply. We highly recommend PEI sheets as the best surface to print on. For Nylon based materials, we still recommend you put a thin layer of the glue stick on it.
-
Why use Ultrasonic cleaners when Wash & Cure units seem to be so easy to use? Short answer, high speed & less manual work. Ultrasonic vibrations loosen out debris from any surface surface efficiently & quickly using harmless forces. The frequency of motion they form safely dislodges uncured resin particles at a microscopic level that other devices cant create. Ultrasonic cleaners can clean most resin parts in 3 mins. Most entry level washers can't beat that. The fact that there is no heavy movement, allows debris to settle rather than float around. This makes it far easier to get the parts clean with less fluid use. When cleaning castable resins or industrial resins in particular, ultrasonic cleaners will give you the edge.
-
Genuine Creatbot door handles. These are the slim thin silver coloured aluminum door handles on newer Creatbot 3d printers with hinged doors. They are the smaller size (approx 80mm long), which are used for DX, DE, F160. They are also used on the rear chamber doors of the F430. These are attached to the Acrylic doors on the D series, & corresponding door frames on F series machines.
-
Why use Ultrasonic cleaners when Wash & Cure units seem to be so popular? Ultrasonic vibrations loosen out debris from any surface surface efficiently & quickly using harmless forces. The frequency of motion they form safely dislodges uncured resin particles at a microscopic level that other devices cant create. Ultrasonic cleaners can clean most resin parts in 3 mins. Most entry level washers can't beat that. The fact that there is no heavy movement, allows debris to settle rather than float around. This makes it far easier to get the parts clean with less fluid use. Resin cleaning liquids like Monocure Resin away & Phrozen now make it a cheaper & safer option than to use IPA or other explosive alcohol based cleaners. When cleaning castable resins or industrial resins in particular, ultrasonic cleaners will give you the edge.
Alex L2023-11-28I have dealt with the 3D Printer Store for several months now and have to say that the experience has been very positive. Zubbin is extremely knowledgeable in this field, enthusiastic, honest and responsive. Pre and Post Purchase customer support has been great. He will have your best interest in mind and will recommend the best product for your needs. My positive experience dealing with him professionally has led me to buy product from him for personal use. We are very lucky to have such a supplier providing these kinds of specialized 3D Printers, Filaments, accessories and services in New Zealand. The rare filaments can sometimes be difficult to source but he will do his best to find alternatives to get what's needed ASAP or even suggest proper alternatives. I am looking forward to future collaboration with this supplier.
Elias Bayless2023-10-18First choice for all my 3d printing needs, the team here really does a great job! Always get my filament here and it arrives really fast and always performs very well in my printer.
Lyle Adams2023-10-18I recently purchased a 3D printer from this business and also took their training. Zubbin's knowledge and assistance is top-notch. He provided valuable insights not only on 3D printing but also related topics. Highly recommended!!
Dylan Cooper2023-09-19Solid company to deal with. I have ordered filament multiple times from this company. I have also been advised on better filament options than what I ordered, which worked out really well. Will continue to shop here!
Maarten van den Heuvel2023-08-21Good prices, fast shipping, excellent communication and when there was a hiccup with my order it was sorted super fast and to my full satisfaction. Can recommend.
Phil Shimmin2023-08-16Great service from these guys. On my most recent order there was a stellar turnaround of only 24 hours between initial stock query and the filament being in my printer.
Dan King2022-09-29Shipping and packaging was excellent and best in market pricing. I had an issue with a misunderstanding about the particular properties of the resin I purchased but Zubbin responded quickly and helped me resolve the issue. Perfect customer service, they have gained a loyal customer.
Mike O2022-09-12These guys are awesome. I used to buy my filament from overseas for my projects and needed something in a hurry and went looking for something local. I'm so glad I did. Not only are the prices as good or better than what I was getting overseas and even more of a deal when considering the pricing I was paying for shipping their turn around each time has been next day. Great range of in stock filaments, good prices, super fast turn around and excellent customer service.
Dion Hitchens2022-08-09Kia ora, This is a fantastic business selling reliable machines at a great price point. What I am impressed with the most is that the owner is always willing to help if I have a problem his insight and knowledge he is so willing to share is always on point and allows me to solve the problem I am trying to resolve. I look forward to doing more business with them. thanks
Michael Williams2022-06-28Sent them an email explaining what I was trying to achieve and asked for their advice. They responded promptly and recommend a basic 3d printer which turned out absolutely fit for purpose. Ordered online and with good communication i had printer within days. Will definitely return when I upgrade. This printing stuff is very addictive.