-
The Teflon feed tube to connect the extruder to the head on Creatbot D series 3d printers like the Creatbot DX, DE etc. Includes the brass studs that the tube plugs into & locks into place. Screws on the head end & the extruder end. No assembly needed. Available for 3mm filament as well as 1.75mm filament based Creatbot D series machines. Please specify filament diameter, otherwise the default 3mm compatible tubes will be sent as they are more common. If your lugs break off, please consider buying this 1 piece ready tube.
-
3D Print your part with this PLA & then Etch / Engrave with your Laser Engraver This unique material is optimized to be used with laser engravers within a 980-1064 nm wavelength. The material has been tested successfully with a Nd:YAG- and  fiberlasers. Laser marking has various advantageous over conventional marking technologies: Bright White Colour - Markings are permanent, waterproof, wear and heat resistant, lightfast and resistant to chemicals. - Flexibility in marking design. - No pre or post-treatment required. Laser marking PLA will not work with CO2 lasers. Please welcome ColorFabb's unique Laser marking Filament all the way from Netherlands & ready to ship right from Auckland.
-
Genuine Creatbot Throat Tube which connects the hot block into the extruder mechanism. This is the Full Matal hot end which doesn't have a teflon liner inside, allowing you to easily print Carbon Fiber as well as high temp materials up to 450C. If you are new to 3d printing, you might find it useful to start with the other Teflon lined heat brake version as it can be easier to print common materials like PLA & ABS with that one. The heat sink & the nozzle is attached at the bottom of this piece. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including F160, F160 PEEK, F430, F430 PEEK, D600 PRO (not the older D600)
-
Genuine Creatbot Throat Tube which connects the hot block into the extruder mechanism. This is the teflon tube lined version which makes it easy to print PLA, PETg etc thanks to the teflon liner. But it will only operate up to 260C, please do not print hotter than that else you will damage the teflon liner. The heat sink & the nozzle is attached at the bottom of this piece. If you have replaced nozzles & still find there are extrusion issues, please consider changing this part. This tube is considered part of the heat break mechanisk, & has a partial teflon coating on the top to aim smooth extrusion. So it is recommend you change this tube as needed for the best uniformity in extrusion as well as reduction of jams or blockages particular in longer 3d prints. Will suit all Creatbot D series 3D Printers we sell including F160, F160 PEEK, F430, F430 PEEK, D600 PRO (not the older D600)
-
Phrozen Ultra High Temperature Resin - now in NZ
Excellent for 3D Prints with high precision & HIGH TEMPERATURE RESISTANCE up to 220 deg C! With 220 deg C temp resistance, the TR300 finally unleashes advanced application capability for low cost REsin 3D Printers. It is also tougher than most resins on the market, & all this for a very affordable price. EASY POST-PROCESSING: Coloring, drilling and grinding are all suitable. This is the upgrade to the popular TR250LV Resin that has been one of the biggest selling resins in our Phrozen brand. A great choice for vulcanized rubber molding process, such as jewelry casting, GK kit, and all other high-heat applications, thanks to high temperature resistance and hardness. Weight 1Kg Grey Colour -
Pet-G is very good functional material & its easier to work with than Abs. It is the same food safe PET thats used in water bottles etc It does not shrink or warp as easily as Abs does, & thus provides good dimensional accuracy for beginners who want to move up from PLA+. It provides excellent finish, high tensile strength, & has a high temperature Glass Transition Temperature of 80 deg C. It is highly recommended for those who want high temperature & high strength properties compared to PLA. Esun PETg 1.75mm 1Kg SOLID GREEN All coloured PETg is slightly translucent compared to other materials.
-
This is a temperature sensing Thermocouple for Creatbot F series 3d printers. They will fit all Creatbot F430 & F160 3d printers.
-
NZ's Best Entry Level Resin 3D Printer Bundle
3D Print parts bigger than common consumer grade machines, & Wash the entire build plate easily in our washer. Then Cure the print with our Lamp. With the Phrozen Mighty 14K Revo 3D Printer you will be printing large parts FAST thanks to its Monochrome LCD, & at High 14K Resolution. With the Phrozen Wash & Cure kit, you can cure large 210x270mm parts! Most cheap curers on the market can't accommodate parts larger than around 120cm. -
Head board for 3d printers like Wanhao i3 plus mk2, D6, D9, D9 mk2 etc. This is the little PCB that sits on top of the main head where you plug in the heater, temp sensors, etc.
-
This is an inductive sensor for 3d printers like Wanhao i3 plus mk2, D6, & D9. It will suit most other 3d printers that use magnetic proximity sensors for bed levelling. Or for any other applications where a magnetic sensor is used for proximity, detection, limit switching etc.
-
Genuine Creatbot high temp 420 degree rated hot end for F series 1.75mm 3d printers. Will suit all Creatbot F 3D Printers we sell including Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers. This hot end will work for all materials upto 420C. This hot end doesnt have a teflon liner so it can be used with abrasive materials like carbon fibre. It will also work for PLA & other common materials. However, for beginners, we sometimes recommend printing those sorts of entry level materials with the standard temp hot end which has a teflon liner, which aids the smoother flow of PLA. So its a little more forgiving for times when your settings may not be quite perfect. However this teflon can be worn off by abrasive materials like Carbon Fiber, so for such materials we recommend printing with the high temp hot end which doesnt have that liner. If you also need a new temperature sensor thermister or thermocouple, or a new cartridge heater, please buy them separately.
-
Genuine Creatbot standard 260 degree rated hot end for F series 1.75mm 3d printers. Will suit all Creatbot F 3D Printers we sell including Creatbot F160, F160 PEEK, F430 & F430 PEEK edition 3d printers. This hot end is only for materials upto 260C. To print hotter, please use buy the High Temp Extruder hot end. The advantage of the standard hot end is that it has a teflon liner inside which aids smooth flow of materials like PLA. However this teflon can be worn off by abrasive materials like Carbon Fiber, so for such materials we recommend printing with the high temp hot end which doesnt have that liner. If you also need a new temperature sensor thermister or thermocouple, or a new cartridge heater, please buy them separately.
Trustindex verifies that the original source of the review is Google.
Alex L2023-11-28I have dealt with the 3D Printer Store for several months now and have to say that the experience has been very positive. Zubbin is extremely knowledgeable in this field, enthusiastic, honest and responsive. Pre and Post Purchase customer support has been great. He will have your best interest in mind and will recommend the best product for your needs. My positive experience dealing with him professionally has led me to buy product from him for personal use. We are very lucky to have such a supplier providing these kinds of specialized 3D Printers, Filaments, accessories and services in New Zealand. The rare filaments can sometimes be difficult to source but he will do his best to find alternatives to get what's needed ASAP or even suggest proper alternatives. I am looking forward to future collaboration with this supplier.Trustindex verifies that the original source of the review is Google.Elias Bayless2023-10-18First choice for all my 3d printing needs, the team here really does a great job! Always get my filament here and it arrives really fast and always performs very well in my printer.Trustindex verifies that the original source of the review is Google.Lyle Adams2023-10-18I recently purchased a 3D printer from this business and also took their training. Zubbin's knowledge and assistance is top-notch. He provided valuable insights not only on 3D printing but also related topics. Highly recommended!!Trustindex verifies that the original source of the review is Google.Dylan Cooper2023-09-19Solid company to deal with. I have ordered filament multiple times from this company. I have also been advised on better filament options than what I ordered, which worked out really well. Will continue to shop here!Trustindex verifies that the original source of the review is Google.Maarten van den Heuvel2023-08-21Good prices, fast shipping, excellent communication and when there was a hiccup with my order it was sorted super fast and to my full satisfaction. Can recommend.Trustindex verifies that the original source of the review is Google.Phil Shimmin2023-08-16Great service from these guys. On my most recent order there was a stellar turnaround of only 24 hours between initial stock query and the filament being in my printer.Trustindex verifies that the original source of the review is Google.Dan King2022-09-29Shipping and packaging was excellent and best in market pricing. I had an issue with a misunderstanding about the particular properties of the resin I purchased but Zubbin responded quickly and helped me resolve the issue. Perfect customer service, they have gained a loyal customer.Trustindex verifies that the original source of the review is Google.Mike O2022-09-12These guys are awesome. I used to buy my filament from overseas for my projects and needed something in a hurry and went looking for something local. I'm so glad I did. Not only are the prices as good or better than what I was getting overseas and even more of a deal when considering the pricing I was paying for shipping their turn around each time has been next day. Great range of in stock filaments, good prices, super fast turn around and excellent customer service.Trustindex verifies that the original source of the review is Google.Dion Hitchens2022-08-09Kia ora, This is a fantastic business selling reliable machines at a great price point. What I am impressed with the most is that the owner is always willing to help if I have a problem his insight and knowledge he is so willing to share is always on point and allows me to solve the problem I am trying to resolve. I look forward to doing more business with them. thanksTrustindex verifies that the original source of the review is Google.Michael Williams2022-06-28Sent them an email explaining what I was trying to achieve and asked for their advice. They responded promptly and recommend a basic 3d printer which turned out absolutely fit for purpose. Ordered online and with good communication i had printer within days. Will definitely return when I upgrade. This printing stuff is very addictive.
